SMOK VMAX MOD Battery (SMOKVMAX)

Description

Smoktech V-Max Variable Voltage Electronic Cigarette

Variable Voltage 3.0 - 6.0V

Uses 2 IMR 18350 batteries, ***INCLUDED***

Discharge voltage: 6v - 8.4v

Quiescent current: Step-down regulator

PCB allows 5 Amperage output limit.

Device measurement :Diameter 21mm * length 110mm

VMax is made of brass and painted black or silver.

Built-in three digit display allows you to visually adjust your voltage.

Available user setting :

Power adjust up

Power adjust down

Power on/off

Battery Check

Atomizer ohm check

LED on/off

button never gets stuck, with a flexible 360° turn around

Vmax user settings:

UU- Power up

UD- Power down

SO- Power on/off

UC- Battery Check

DS - display information setting

*do- atomizer output voltage

*du- battery output voltage

*dR - atomizer ohm

LO- LED on/off

Power Adjust Up:

1. Press the button 3 times in a row until "UU" is shown on the display.

2. When UU is shown on the display, leave the button idle for 2 seconds. The display will change to show the last voltage selected.

3. Once the voltage is displayed, each time you press the button the voltage will advance to the next higher setting: 3.1,3.2,3.3 etc. When you reach 6.0, it will rotate back to 3.0 and go up again.

4. When you have reached the desired setting, leave the button idle for 2 seconds. The setting will be saved and VV will resume normal operation.

Power Adjust Down:

1. Press the button 4 times in a row until "UD" is shown on the display .

2. When UD is shown on the display , leave the button idle for 2 seconds. The display will change to show the last voltage selected.

4. Once the voltage is displayed, each time you press the button the voltage will advance to the next lower setting: 5.9,5.8,5.7 etc. When you reach 3.0, it will rotate back to 6.0 and go up again.

4. when you have reached the desired setting, leave the button idle for 2 second. The setting will be saved and VV will resume normal operation.

Power On/Off:

1. Press the button 5 times in a row until "SO" is shown on the display.

2. When UD is shown on the display, leave the button idle for 2 seconds. The display will show the last setting, on or off .

4. Each time you press the button the display will toggle between on/off.

4. When you have reached the desired setting, leave the button idle for 2 seconds. If you selected "OF" the VV will go into standby mode.

Battery Check:

1. Press the button 6 times in a row until UC is shown on the display.

2. When UC is shown on the display, leave the button idle for 2 seconds, the digital display will show your battery voltage measurement.

3. The battery voltage will be displayed for 2 seconds, then the display will turn off.

Display Information Setting During Vaping:

1. Press the button 7 times in a row until DS is shown on the display,

2. When DS is shown on the display, leave the button for 2 seconds, the display will show the current setting: DO, DU or DR.

3. Each time you press the button, the setting will toggle among "DO" "DU" or "DR" ,

4. When "DO" is chosen, leave the button idle for 2 seconds, the setting will be saved and the display will show your atomizer working output voltage during your vaping;

5. When "DU" is chosen, leave the button idle for 2 second, the setting will be saved and the display will show your battery voltage during your vaping.

6. When "DR" is chosen, leave the button idle for 2 seconds, the setting will be saved and the display will show your atomizer resistance during your vaping.

LED On/Off

1. Press the button 8 times in a row until "LO" is shown on the display.

2. When LO is shown on the display, leave the button idle for 2 seconds, the display will show the current setting: ON/OFF .

3. Each time you press the button, the setting will toggle between on/off.

4. When you have reached the desired setting, leave the button idle for 2 seconds. The setting will be saved and VV will resume normal operation.

Short Circuit Protection:

The display will show the below error code when there is a short circuit:

1. F1: resistance for the heating coil of cartomizer is bigger than 0.5R, or smaller than 1.3R

2. F2: resistance for the heating coil of cartomizer is smaller than 0.5R